Filter
Sort:
Show:
ENGINEER’S STEEL PARALLELS & SETS

ENGINEER’S STEEL PARALLELS & SETS

In Stock
  • Very useful milling & drilling .
  • Made from alloy steel.
  • Properly hardened & ground.
FLY TOOL CUTTER HOLDERS- TAPER SHANK

FLY TOOL CUTTER HOLDERS- TAPER SHANK

In Stock
 A fly cutter usually has two cutting heads and it is able to cut with a constant depth to face any surface to obtain a uniform surface.
FLY TOOL CUTTER TAPER

FLY TOOL CUTTER TAPER

In Stock
  • A fly cutter usually has two cutting heads and it is able to cut with a constant depth to face any surface to a obtain a uniform surface
  • fly cutters are used in automobile industry for various facing jobs
  • in motor industry fly cutters are used extensively
  • in almost all occasions they are used for the facing
3PC FLY TOOL CUTTER FOR ROUND BITS

3PC FLY TOOL CUTTER FOR ROUND BITS

In Stock
  • As the name suggest these are made for Round bits.
  • Very fine surface finish is obtain than the face mill.
FLY TOOL CUTTERS-WITH SUITABLE TOOL BITS

FLY TOOL CUTTERS-WITH SUITABLE TOOL BITS

In Stock
  • Purpose of Fly Cutters is very important in face Milling.
  • These are most commonly used by manual machinist.
Engineer’s Steel Parallels & Sets

Engineer’s Steel Parallels & Sets

In Stock
This set features a variety of sizes, including 1/2 in., 5/8 in., 3/4 in., 7/8 in., 1 in., 1-1/8 in., 1-1/4 in., 1-3/8 in., 1-1/2 in. and 1-5/8 in. W. Each parallel measures in at 6 in. L and 1/8 in. thick.
Wavy Parallel Set of 8 Pairs

Wavy Parallel Set of 8 Pairs

In Stock
For supporting a work piece in a machine vice, to elevate the workpiece above the vice jaws.
V Sine Bars

V Sine Bars

In Stock
  • Hardened & ground.
  • Clamp included.
  • Accurate to .0005"
  • 1" round capacity
Sine Bars

Sine Bars

In Stock
Use of product - Combo Edge Finder installs in Collet or chuck of milling machine. Precisely locates edge of workpiece relative to center of spindle. Works in both feed directions for quick and easy use.  
Vee Block stepped groove

Vee Block stepped groove

In Stock
  • Supplied in matched pairs.
  • Holds both square and round job.
  • clamps Included.
  • Side hole provided in each clamp to provide clamping from side.
Steel Vee Blocks

Steel Vee Blocks

In Stock
  • Supplied in matched pairs.
  • Made of best quality steel, hardened throughout.
  • Accurately machined & precision ground to extreme accuracy.
Elongated V Blocks

Elongated V Blocks

In Stock
  • All Side precision ground parallel and square.
  • "V" Grooves ground central & Parallel and square.
  • Perfect alignment in matched pair..
  • Holds the square and round work.
Vee Blocks – Non Protruding

Vee Blocks – Non Protruding

In Stock
  • Supplied in matched pairs.
  • Made of best quality steel, hardened throughout up to 55 - 60 HRC
  • Accurately machined & precision ground to extreme accuracy.
Cast Iron Vee Block

Cast Iron Vee Block

In Stock
  • Made from quality casted seasoned steel.
  • Supplied in matched pairs.
  • The "V" is accurate to 900.
  • Very useful tool for laying out round work & holding it for machining
Toolmaker’s Ultimate Vee Blocks

Toolmaker’s Ultimate Vee Blocks

In Stock
  • Block is hardened & ground.
  • Made of Alloy Steel.
  • Provided with one blacodized clamp.
  • The design offers greater versatility to this vee block : capable of being used on base, on end flat in either side as the clamp is within the outside width of the block.
 
Four Way Vee Blocks

Four Way Vee Blocks

In Stock
  • Made from quality casted seasoned steel.
  • Supplied in matched pairs.
  • Very useful tool for laying out round work & holding it for machining
  • Each block incorporates 4 different sized V's, therefore support wide range of jobs.

Filter Products

Categories

Product Status