Filter
Sort:
Show:
MINI VERTICAL SLIDE

MINI VERTICAL SLIDE

In Stock
  • Suitable for Bench Lathes upto 150mm Swing
  • Vertical Travel 70mm
  • Base Dimension: 50x55mm
  • Sliding Table: 90x50mm
  • Dial Graduated to 0-50
  • High Grade casting and Smooth Finish.
LIVE TAILSTOCK

LIVE TAILSTOCK

In Stock
  • Manufactured from high grade steel hardened point hardened point to impart extra strength.
  • These have single row bearings & Taper Rolling to take up radial load and thrust bearings to absorb axial loads.
  • 3 jaws self centering 50mm lathe chuck.
LIVE CENTERS HIGH PRECISION (EXTENDED NOZZLE)

LIVE CENTERS HIGH PRECISION (EXTENDED NOZZLE)

In Stock
  • Body is constructed from hardened and ground steel.
  • eccentricity between .005 - .010
  • Nozzle is assembled with double angular contact bearing.
  • Needle roller bearing at the end of the points in the shank.
BEVEL REVOLVING TUBE PIPE CENTERS

BEVEL REVOLVING TUBE PIPE CENTERS

In Stock
  • Machining Pipes And Similar Hollow Shaft Materials With a High Thrust Capacity.
  • Bevel Section Is Ground After assembly Running In Its Own Bearing.
  • Designed to hold hollow & pipe Works.
  • Manufactured from heat treated high carbon Alloy steel.
LATHE CENTER / DEAD CENTER – FULL

LATHE CENTER / DEAD CENTER – FULL

In Stock
  • Solid Construction WIth No Moving Parts And Fully Hardened.
  • Tip Hardened to 60-63 HRC And Included Angle At Tip is 60°.
  • Hardened High Speed Centers Ensure Long Life.
  • Carbide Tipped Centers Give Longer Tool Life & Require Less Grinding.
  • Covers Widest Range Of Center Hole Sizes.
  • Eliminates Special Centers.
LATHE CENTER / DEAD CENTER – HALF

LATHE CENTER / DEAD CENTER – HALF

In Stock
  • Solid Construction With No Moving Parts And Fully Hardened.
  • Tip Hardened to 60-63 HRC And Included Angle At Tip is 60°.
  • Hardened High Speed Centers Ensure Long Life.
REVOLVING CENTER 7 TIPS

REVOLVING CENTER 7 TIPS

In Stock
  • Set Contents - 5 Diff. live centers, 1 Pipe Center, 1 Female Center & 1 Ejecting Key.
  • Assembled with three bearings.
  • Ecentricity between .005 - .010 μ
  • Body is constructed from hardened and ground steel.
  • Widely used by Modelmakers & Woodworkers on mini lathes.
MINI LIVE CENTERS

MINI LIVE CENTERS

In Stock
  • Manufactured from Case Hardened Steel.
  • GRC-7887 is suitable for EMCO Compact & Similar Sized Lathes
REVOLVING CENTER SLIM BODY / LIVE CENTER SLIM BODY

REVOLVING CENTER SLIM BODY / LIVE CENTER SLIM BODY

In Stock
  • High Precision Bearings.
  • Ultra Slim Design of the body.
  • Slim Nozzle.
  • Three-way running in ball bearings for highest precision.
  • Manufactured from hardened steel.
REVOLVING CENTER / LIVE CENTER

REVOLVING CENTER / LIVE CENTER

In Stock
  • Manufactured from high grade steel hardened point to impart extra strength.
  • Hardened & Ground Steel With 60° Tip Angle.
  • Recommended for use upto 1500 r.p.m
Vee Block stepped groove

Vee Block stepped groove

In Stock
  • Supplied in matched pairs.
  • Holds both square and round job.
  • clamps Included.
  • Side hole provided in each clamp to provide clamping from side.
Steel Vee Blocks

Steel Vee Blocks

In Stock
  • Supplied in matched pairs.
  • Made of best quality steel, hardened throughout.
  • Accurately machined & precision ground to extreme accuracy.
Elongated V Blocks

Elongated V Blocks

In Stock
  • All Side precision ground parallel and square.
  • "V" Grooves ground central & Parallel and square.
  • Perfect alignment in matched pair..
  • Holds the square and round work.
Vee Blocks – Non Protruding

Vee Blocks – Non Protruding

In Stock
  • Supplied in matched pairs.
  • Made of best quality steel, hardened throughout up to 55 - 60 HRC
  • Accurately machined & precision ground to extreme accuracy.
Cast Iron Vee Block

Cast Iron Vee Block

In Stock
  • Made from quality casted seasoned steel.
  • Supplied in matched pairs.
  • The "V" is accurate to 900.
  • Very useful tool for laying out round work & holding it for machining
Toolmaker’s Ultimate Vee Blocks

Toolmaker’s Ultimate Vee Blocks

In Stock
  • Block is hardened & ground.
  • Made of Alloy Steel.
  • Provided with one blacodized clamp.
  • The design offers greater versatility to this vee block : capable of being used on base, on end flat in either side as the clamp is within the outside width of the block.
 

Filter Products

Categories

Product Status